MPO 100m Fiber Transceiver Module Cisco 100G Base SR4 QSFP28 MMF 850nm
Description
Cisco Compatible 100GBase SR4 QSFP28 MMF 850nm MPO 100m Transceiver Module manufactured by ANC International Co., Limited is a parallel 100Gb/s Quad Small Form-factor Pluggable (QSFP28) optical module. It provides increased port density and total system cost savings. The QSFP28 full-duplex optical module offers 4 independent transmit and receive channels, each capable of 25Gb/s operation for an aggregate data rate of 100Gb/s on 100 meters of OM4 multi-mode fiber.
An optical fiber ribbon cable with an MTP/MPO connector can be plugged into the QSFP28 module receptacle. Proper alignment is ensured by the guide pins inside the receptacle. The cable usually cannot be twisted for proper channel to channel alignment. Electrical connection is achieved through an MSA-compliant 38-pin edge type connector.
The module operates by a single +3.3V power supply. LVCMOS/LVTTL global control signals, such as Module Present, Reset, Interrupt and Low Power Mode, are available with the modules. A 2-wire serial interface is available to send and receive more complex control signals, and to receive digital diagnostic information. Individual channels can be addressed and unused channels can be shut down for maximum design flexibility.
The product is designed with form factor, optical/electrical connection and digital diagnostic interface according to the QSFP28 Multi-Source Agreement (MSA). It has been designed to meet the harshest external operating conditions including temperature, humidity and EMI interference. The module offers very high functionality and feature integration, accessible via a two-wire serial interface.
Features
4 independent full-duplex channels
Up to 28Gb/s data rate per channel
QSFP28 MSA compliant
Compliant to IEEE 802.3bm 100GBASE-SR4
Up to 100m OM4 MMF transmission
Operating case temperature: 0 to 70℃
Single 3.3V power supply
Maximum power consumption 2.5W
MTP/MPO optical connector
RoHS-6 compliant
Applications
Rack to Rack
Data Center
Infiniband QDR, DDR and SDR
100G Ethernet
Optical Characteristics (TOP=25°C, Vcc=3.3 Volts)
| Parameter | Symbol | Min | Typical | Max | Units | Notes |
| Transmitter |
| Center Wavelength | λC | 840 | 850 | 860 | nm | |
| RMS Spectral Width | ∆λrms | | | 0.6 | nm | |
| Average Launch Power, each Lane | | -8.4 | | 2.4 | dBm | |
| Optical Modulation Amplitude (OMA), each Lane | OMA | -6.4 | | 3 | dBm | 1 |
| Difference in Launch Power between any Two Lanes (OMA) | Ptx,diff | | | 4 | dB | |
| Launch Power in OMA minus TDEC, each Lane | | -7.3 | | | dBm | |
| Transmitter and Dispersion Eye Closure (TDEC), each Lane | | | | 4.3 | dB | |
| Extinction Ratio | ER | 2 | | | dB | |
| Optical Return Loss Tolerance | TOL | | | 12 | dB | |
| Encircled Flux | | ≥ 86% at 19um; ≤ 30% at 4.5um | | |
| Transmitter Eye Mask Definition {X1, X2, X3, Y1, Y2, Y3}, 5×10–5 hits/sample | | {0.3,0.38,0.45,0.35,0.41,0.5} | | 2 |
| Average Launch Power OFF Transmitter, each Lane | Poff | | | -30 | dBm | |
| Receiver |
| Center Wavelength | λC | 840 | 850 | 860 | nm | |
| Damage Threshold, each Lane | THd | 3.4 | | | dBm | 3 |
| Average Receive Power, each Lane | | -10.3 | | 2.4 | dBm | |
| Receiver Reflectance | | | | -12 | dB | |
| Receive Power (OMA), each Lane | | | | 3 | dBm | |
| Receiver Sensitivity (OMA), each Lane | SEN | | | -9.2 | dBm | |
| Stressed Receiver Sensitivity (OMA), each Lane | | | | -5.2 | dBm | 4 |
| LOS Assert | LOSA | -30 | | | dBm | |
| LOS Deassert | LOSD | | | -12 | dBm | |
| LOS Hysteresis | LOSH | 0.5 | | | dB | |
Notes:
1. Even if the TDP < 0.9 dB, the OMA min must exceed the minimum value specified here.
2. See Figure 5 below.
3.The receiver shall be able to tolerate, without damage, continuous exposure to a modulated optical input signal having this power level on one lane. The receiver does not have to operate correctly at this input power.
4.Measured with conformance test signal at receiver input for BER = 1x10-12.
Product Tags:
|
|
850nm Cisco Fiber Optic Transceiver Images
|
